Even if you’re not very experienced with bath or plumbing projects, many of the steps necessary for replacing an old or damaged shower faucet are relatively simple. This project guide will show you how to replace a shower faucet.

Tip: When learning how to change a shower faucet, first block the shower drain with a cloth to prevent small parts from falling into the opening. Place a blanket or piece of cardboard on the floor of your tub or shower base to protect against dropped tools.

Turn Off the Water

Turn off the water supply.
Unless you happen to have a separate cutoff valve installed in the bathroom, shut off the water to the whole house.
Open up a faucet at a lower level in your home to relieve pressure in the lines and leave it open as you work.

Tip: Choose a faucet with integral stops to make any necessary maintenance easier. Integral stops let you service a single faucet without having to turn off the main water supply.

Remove Old Trim

When replacing a shower faucet, take off the shower head by turning the connecting nut counterclockwise with a pair of pliers.
Faucet handles can be removed in different ways. Some have a cover plate, which can be pried off with a small screwdriver. Others, like the one featured in this video, have a small set screw somewhere on the handle. Once it’s loosened with an Allen wrench, you can remove the handle to gain access to the parts below.
The remaining components of the handle either unscrew or pull off. Keep removing parts until you reach the valve in the wall. If you have a tub spout, this will either be removed with a set screw, or will twist off by turning counterclockwise.

Tip: To protect the finish, wrap a cloth around the connection first and hold the shower pipe with your other hand to keep it from turning inside the wall.

Remove Old Valve and Choose New Valve

To put in a new shower valve, you’ll first need to remove the old one from inside your shower.
To gain access, cut out a section of drywall approximately a foot square on the other side of the wall from your shower valve.
To locate the valve, drill a pilot hole or two from the bathroom side next to the valve with a long bit.
Measure an even square on the back wall, and cut the section out with a drywall saw.
The valve is mounted to a stringer running between the studs.
Cut the copper pipe with a tubing cutter. Cut the pipe going up to the shower, as well as the hot and cold lines below.
Once the pipe is cut, use a reciprocating saw to take out the stringer with the old valve still attached.
Now, it's time to choose a new valve.
Make sure you purchase the correct valve for the faucet you’re planning to install in your shower. It should have two inlet channels for the hot and cold water, and two outlet channels for the tub spout and showerhead. Each of these fittings connects to your pipe either through male threads on the outside or female solder ports on the inside.
Be sure to know the type of plumbing you have in the house before you purchase fittings. For instance, if you have PEX, or cross-linked polyethylene plumbing, you will need to either buy a valve with PEX fittings or you'll need to get the correct adaptors to attach the PEX lines to the valve.
If your bathroom has either a tub or shower only, then the second outlet channel will need to be capped off in the installation. Shower-only valves are also available for bathrooms without a tub.
The valve itself must come out the correct distance from the wall, and is mounted to a stringer, which is a brace running between the studs.
Allow for the depth of the valve, the water-resistant drywall and the thickness of the tile or shower enclosure when setting the proper depth for the stringer. The instructions that come with the valve will show the correct dimensions for the valve and its plumbing.

Sweat the Pipes

To connect to the valve, attach female adapters to the ends of the copper pipe. To ensure a leak-free connection, fittings should be soldered using a torch and lead-free solder. This process is also called sweating the pipes.
Use a deburring tool to clean up the ends of the pipe. Insert it over the end and rotate it around several times until the section is shiny.
Use the wire brush to clean the inside of the fitting.
Apply a light coating of solder paste or flux to the inside of the valve fittings, and to the cleaned end of the copper pipe. Insert the end of the pipe all the way into the adapter.
Use a torch to heat up the middle of the fitting. Apply solder to the joint between the pipes, letting it melt into the seam all the way around. Don’t overdo it – the flux will dissolve oxides and draw the solder into the seam.

If you are interested in making the connection without using a torch, solderless connectors can be used. Simply push on and lock.

You must use the special tools indicated on the manufacturer’s packaging to release the compression fitting.
When using solderless connectors, make sure to thoroughly clean the ends of each pipe, and allow 7/8 inch for the connector to overlap each side of the pipe. If you’re making connections to the threaded fittings, make sure you apply a layer of Teflon tape to the threads before installing.

Assemble the New Valve Section

Make sure you purchase the correct valve for the faucet you’re planning to install in your shower. It should have two inlet channels for the hot and cold water, and two outlet channels for the tub spout and shower head. Each of these fittings connects to your pipe either through male threads on the outside or female solder ports on the inside.
If your bathroom has either a tub or shower only, then the second outlet channel will need to be capped off in the installation. Shower-only valves are also available for bathrooms without a tub.
The valve itself must come out the correct distance from the wall, and is mounted to a stringer, which is a brace running between the studs.
Allow for the depth of the valve, the water-resistant drywall, and the thickness of the tile or shower enclosure when setting the proper depth for the stringer. The instructions that come with the valve will show the correct dimensions for the valve and its plumbing.

Install a Stringer and Test for Leaks

The new valve must be set to the correct depth in the wall for the faucet to install properly. It should account for the thickness of the drywall, as well as the tile or shower enclosure on your walls. Most valves come with instructions or a guide to help you get the dimensions right. The valve is mounted to a stringer, which is a cross piece support in the wall.
In most bathroom installations, the stringer would be set to the proper depth first, and the valve will be mounted to it. But since we’re replacing a faucet in an existing bathroom, we’ll need to install our supports from the opposite side.
Now, test for leaks. Before beginning the test, cap off the shower head and tub spout connections if you have them.
If it’s not already installed, screw the test cap onto the valve, and tighten down the bonnet nut holding it on.
Have someone turn the water back on while you check all the connections to make sure there are no leaks.
If you don’t see any leaks, turn the water back off, remove the caps and patch up the wall.

Install the Cartridge

Each shower faucet will have specific installation instructions, so follow the directions in your owner’s manual. Some valves come with a cartridge already installed. If yours does, you can skip this step. Other manufacturers include the cartridge as part of the faucet you purchase, and it needs to be installed into the valve first.
To install the cartridge for this faucet, make sure it’s positioned correctly according to the manufacturer’s instructions.
Push it firmly into the valve, making sure the marks on the shower cartridge line up with the slots on the valve. When inserted properly, it should have a snug fit.
Screw on the bonnet nut and tighten it down with pliers.

Install the Tub Spout

To install the tub spout, solder the enclosed adapter to the outlet pipe.
Apply a layer of flux to the outside of the surface.
Remove the O-ring and any other components that could be damaged from the heat then slide the adapter over the pipe.
Use a torch to heat up the adapter, and apply a small bead of solder to the outside seam.
Place a piece of cardboard inside the tub to catch any drips. After it cools, place the O-ring back on and screw the tub spout onto the adapter by turning it clockwise.

Install the Shower Head and Optional Handshower

All shower heads install basically the same way, simply by screwing the nut onto the threads of the shower arm.
Before installing, wrap some Teflon tape clockwise around the threads of the arm.
Screw the shower head onto the threads until tight.
Attach one end of the hose to the handshower.
When learning how to replace a shower hangle, it's important to understand there will be some type of sleeve that slides over top of the cartridge and valve. Make sure to include any O-ring and spacer that’s called for in the installation.
The escutcheon goes around the sleeve against the wall, and is held in place by screws.

The last step to tackle when learning how to replace a shower faucet is to test and make sure to set your temperature levels.

To prevent scalding, set the outlet temperature on your shower no higher than 120 degrees.
Turn on the water supply and make sure there are no leaks, then slip on the handle and turn the water to the hottest position.
Test the temperature, then turn off the water and remove the handle to gain access to the temperature limit stop. This is usually a ring or clip that’s pried up, turned either clockwise or counterclockwise according to the needed adjustment. Then reinsert the ring or clip.
Follow your faucet’s instructions and check after each adjustment until you reach the desired maximum temperature.

Tip: At the end of the process, you may opt to install an access panel to cover the opening rather than replace the drywall, making it easier to access the area in the future.

Learning how to replace a shower faucet can be done in just a few hours, but if you prefer a professional handle the project, consider using our bathroom installation services to get the job done. Need help identifying a tool or material for replacing a shower faucet? Find products fast with image search in The Home Depot app. Snap a picture of an item you like and we'll show you similar products.

How to Replace a Shower Faucet